作业帮求高手帮忙用英语翻译一下一段话,在线等,急!
来源：学生作业帮 编辑：拍题作业网作业帮 分类：英语作业 时间：2024/04/26 10:22:30
求高手帮忙用英语翻译一下一段话,在线等,急!
求高手帮忙用英语翻译一下一段话,与化工设计设备有关,希望不是机译,采用加分!先感谢一下~
3.1 内部斜梯的材质按设备图样上的规定（根据使用介质环境确定）.一般采用Q235-A.F钢；当容器壳体材质为高合金钢时,斜梯的材质应与容器壳体（内壁）材质一致.
3.2 零件的机加工粗糙度Ra≤25μm,切边粗糙度≤50μm,梯梁周边不得有毛刺.
3.3 内部斜梯焊接完毕后不得翘曲,踏步两端焊脚打磨光滑,斜梯安装后应稳定牢固.
求高手帮忙用英语翻译一下一段话,与化工设计设备有关,希望不是机译,采用加分!先感谢一下~
3.1 内部斜梯的材质按设备图样上的规定（根据使用介质环境确定）.一般采用Q235-A.F钢；当容器壳体材质为高合金钢时,斜梯的材质应与容器壳体（内壁）材质一致.
3.2 零件的机加工粗糙度Ra≤25μm,切边粗糙度≤50μm,梯梁周边不得有毛刺.
3.3 内部斜梯焊接完毕后不得翘曲,踏步两端焊脚打磨光滑,斜梯安装后应稳定牢固.
3.1 内部斜梯的材质按设备图样上的规定（根据使用介质环境确定）.一般采用Q235-A.F钢；当容器壳体材质为高合金钢时,斜梯的材质应与容器壳体（内壁）材质一致.
Material of the inclined ladder inside should be consistent with specifications on the equipment drawing(determined by environmental conditions of the material).In general cases,Q235-A.F steel will be used.When the container shell is high-alloy steel,the inclined stairs should be consistent with the container shell(inwall) in material.
3.2 零件的机加工粗糙度Ra≤25μm,切边粗糙度≤50μm,梯梁周边不得有毛刺.
Roughness for parts machined:Ra≤25μm,trimming cut roughness ≤50μm; periphery of the girder should be void of burrs.
3.3 内部斜梯焊接完毕后不得翘曲,踏步两端焊脚打磨光滑,斜梯安装后应稳定牢固.
The inside inclined ladder should be void of warpage after welding.Both ends of the stairs should be sanded into smoothness and the inclined ladder should be stable and firm after installation.
Material of the inclined ladder inside should be consistent with specifications on the equipment drawing(determined by environmental conditions of the material).In general cases,Q235-A.F steel will be used.When the container shell is high-alloy steel,the inclined stairs should be consistent with the container shell(inwall) in material.
3.2 零件的机加工粗糙度Ra≤25μm,切边粗糙度≤50μm,梯梁周边不得有毛刺.
Roughness for parts machined:Ra≤25μm,trimming cut roughness ≤50μm; periphery of the girder should be void of burrs.
3.3 内部斜梯焊接完毕后不得翘曲,踏步两端焊脚打磨光滑,斜梯安装后应稳定牢固.
The inside inclined ladder should be void of warpage after welding.Both ends of the stairs should be sanded into smoothness and the inclined ladder should be stable and firm after installation.