作业帮 > 英语 > 作业

英语翻译detailed descriptionoperating principleThe TPS6031X char

来源:学生作业帮 编辑:拍题作业网作业帮 分类:英语作业 时间:2024/03/29 18:00:16
英语翻译
detailed description
operating principle
The TPS6031X charge pumps are voltage quadruplers that provide a regulated 3.3-V or 3-V output from a 0.9-V
to 1.8-V input.They deliver a maximum load current of 20 mA.Designed specifically for space critical battery
powered applications,the complete converter requires only five external capacitors and enables the design to
use low-cost,small-sized,1-μF ceramic capacitors.The TPS6031X circuits consist of an oscillator,a voltage
reference,an internal resistive feedback circuit,two error amplifiers,two charge pump stages with MOSFET
switches,a shutdown/start-up circuit,and a control circuit.
snooze mode
The devices contain a circuit which dramatically reduces the quiescent current at light loads.This so called
snooze mode must be enabled by pulling the SNOOZE pin low.When the output current decreases below the
snooze mode threshold,the device enters the snooze mode.In snooze mode,the main error amplifier with 4%
error and 50-μA supply current is disabled and a 10%,2-μA regulator controls the output voltage.
start-up procedure
The start-up performance of the device is independent of the level of the snooze input.When voltage is applied
to the input,CP1 will first enter a dc start-up mode during which the capacitor on OUT1 is charged up to about
VIN.After that,it starts switching to boost the voltage further up to about two times VIN.CP1 first enters a dc
start-up mode during which the capacitor on OUT1 is charged up to about VIN.CP2 then follows and charges
up the capacitor on OUT2 to about the voltage on OUT1,after that,it also starts switching and boosts up the
voltage to its nominal value.The voltage at the SNOOZE pin must not exceed the highest voltage applied to
the device.
NOTE:
During start-up with VOUT = 0 V,the highest voltage is the input voltage.
power-good detector
The power-good output is an open-drain output on the TPS60310 and TPS60311 or a push-pull output on the
TPS60312 and TPS60313.The PG-output pulls low when the output of OUT2 is out of regulation.When the
output rises to within 98% of regulation,the power-good output goes active high.In shutdown,power-good is
pulled low.In normal operation,an external pullup resistor with the TPS60310 and TPS60311 is typically used
to connect the PG pin to VOUT.The resistor should be in the 100-kΩ to 1-MΩ range.If the PG output is not used,
it should remain unconnected.Output current at PG (TPS60312,TPS60313) reduces maximum output current
at OUT2.
In snooze mode,the output voltage is sampled at a rate up to 2 ms and is applied to the power-good comparator.
In normal mode,the output voltage is measured continuously.
详细说明
工作原理
该TPS6031X电荷泵电压quadruplers是提供了一个规范3.3 - V或3 - V输出从0.9电压
1.8 - V输入.他们提供的最大负载电流20毫安.专为空间关键电池
供电的应用,彻底转换,只需要5个外部电容,使设计
使用成本低,小规模,1 μF陶瓷电容器.该TPS6031X电路组成的振荡器,电压
范围,内部电阻反馈电路,两个误差放大器,两个阶段的电荷泵的MOSFET
开关,关机/启动电路,以及控制电路.
打盹模式
该器件包含一个电路,极大地降低了静态电流在轻负载.这所谓的
打盹模式必须启用拉低延期引脚低.当输出电流减少低于
打盹模式的阈值,该设备进入睡眠模式.在睡眠模式下,主要误差放大器的4 %
错误,50微安电源电流是残疾人和10 % ,2 -电流调节器控制输出电压.
启动程序
启动性能的装置是独立的水平打盹的投入.当电压应用于
输入,CP1将首先进入一个直流启动模式在此期间,电容OUT1收取高达约
VIN的.在此之后,它开始转向提高电压进一步达到约2倍的VIN .CP1首次进入特区
启动模式在此期间,电容OUT1收取高达约的VIN .然后如下的CP2及收费
的电容OUT2约上的电压OUT1 ,在此之后,它也开始转换和提升了
它的额定电压值.电压引脚的延期不得超过最高电压适用于
该设备.
注意:
在启动过程中的输出电压= 0五,最高电压为输入电压.
电源良好探测器
电源良好输出是开漏输出的TPS60310与TPS60311或推挽输出的
TPS60312与TPS60313 .该指引输出拉低产出的OUT2超出规定.当
输出上升到98 %的范围内调节,电源良好输出不用积极高.在关断,电源良好的
拉低.在正常操作时,一个外部上拉电阻与TPS60310与TPS60311通常使用
连接素引脚和Vout .电阻应在100 kΩ至1 MΩ范围.如果前列腺素输出没有使用,
它应继续无关.输出电流素( TPS60312 ,TPS60313 )降低最大输出电流
在OUT2 .
在睡眠模式下,输出电压的取样率高达2毫秒,是适用于电源良好比较器.
在正常模式下,输出电压是连续测量.
不用谢我,是用Google翻译的,其实下次你可以直接去百度输入翻译,我个人比较喜欢Google的翻译,比较好,你直接进去就可以了!网址是http://translate.google.cn